How to Read an InBody or Body Composition Report, Line by Line

by By Prakash Hospital

A man standing on a body composition analyser and holding its hand electrodes

The machine estimates fat and muscle from how a tiny electric current passes through the body.

A body composition report looks intimidating the first time you see it: bar charts, percentages, a score out of 100, a figure of a human body with numbers around it. The good news is that it answers four plain questions. How much of you is fat? How much is muscle? Where is each located? And are your fluid levels normal?

This guide goes through a typical InBody-style printout section by section. Different brands (InBody, Tanita, Omron, Withings, gym machines) arrange things differently and use their own formulas, so your report may not match exactly, but the main sections are very similar. We'll point out what to act on and what to ignore.

First, remember what these machines are

A body composition analyser uses bioelectrical impedance analysis (BIA). It sends a tiny electric current through your body and measures resistance. Water-rich lean tissue conducts well; fat conducts poorly. Software combines the resistance with your height, age and sex to estimate fat and lean mass.

Two consequences matter for everything below:

  1. It's an estimate. The numbers can be several percentage points off compared with DEXA, and the machine can't be trusted to the decimal.
  2. It's sensitive to hydration. Test conditions (morning, fasted, after the toilet, no heavy exercise in the previous 12 hours) change the result. Compare reports only when taken under similar conditions on the same machine.

Section 1: body composition analysis

This is usually the top-left block. It splits your weight into four parts.

| Item | What it is | |---|---| | Total body water (TBW) | All water in your body, inside and outside cells | | Protein | Mostly muscle protein | | Minerals | Mostly bone | | Body fat mass (BFM) | Weight of fat |

Added together, they equal your weight. Lean body mass = water + protein + minerals (some reports also list "fat-free mass").

What to look at

  • Water should make up roughly 50 to 60 percent of body weight in adults (lower in women and in people with more fat).
  • Protein and minerals matter mainly as a trend. A falling protein number over months suggests muscle loss.
  • Body fat mass in kilograms is more motivating to track than percentage, because it moves in plain terms. Losing 3 kg of fat shows up as 3 kg.

Section 2: muscle-fat analysis

A set of horizontal bars compares three numbers: weight, skeletal muscle mass (SMM) and body fat mass. Each bar has a "normal range" shaded in the middle.

How to read it

The bars show how your values sit relative to the machine's reference range for your height.

  • Weight bar in normal range, muscle bar below, fat bar above: a classic "skinny-fat" pattern. Your weight looks fine while your composition isn't. Common in India.
  • Weight above range, muscle above, fat in normal range: you're heavy because you're muscular.
  • All three above: overweight with both muscle and fat.
  • Weight below range and muscle below range: underweight with low muscle mass, which deserves a closer look at nutrition and health.

A rule of thumb that machines use is the "C", "I" or "D" shape formed by the three bars. A "D" shape (muscle bar longer than weight, fat in range) is the one you're aiming for. Don't obsess about the shape names. What matters is moving muscle up and fat down.

Section 3: obesity analysis

This block shows two numbers.

BMI (body mass index): weight divided by height squared. The machine's normal range is usually 18.5 to 25. For Asian Indians, risk begins earlier (overweight from 23, obese from 25), so don't be reassured by "normal" on the printout when the number is 23 or above (Misra and Shrivastava, Nutrients, 2013).

PBF (percent body fat): fat mass divided by weight. Machines typically show a normal range of 10 to 20 percent for men and 18 to 28 percent for women. Standard fitness charts put the "average" band higher, and risk in South Asians begins at lower body fat levels, so aim toward the lower half of these ranges.

Watch the pair together

BMI normal with PBF high means your weight is "right" but you have too much fat and too little muscle. This is the pattern that BMI alone hides.

Section 4: segmental lean analysis

A drawing of the body shows lean mass in each region: right arm, left arm, trunk, right leg, left leg. Each region lists kilograms and a percentage, often compared with what would be expected for your weight.

What to look for

  • A percentage under 100 means you have less lean mass in that region than the machine expects.
  • Left-right differences greater than about 5 to 10 percent can reflect handedness, an old injury or uneven training. Large asymmetry after an injury is a reason to ask a physiotherapist.
  • Low legs, normal arms: common in sedentary people who do some upper-body exercise. Legs hold the most muscle, and building leg strength pays off most for blood sugar and mobility.
  • Low trunk lean mass may reflect poor core muscle or, rarely, measurement artefacts.

Segmental figures are less reliable than whole-body ones. Hydration or tension in a limb can distort them, so look for trends and big differences, not small ones.

Section 5: segmental fat analysis

Same drawing, but for fat. It shows where your fat sits.

  • Fat concentrated in the trunk (belly) is the pattern linked to diabetes and heart disease.
  • Fat mostly in hips and thighs carries less metabolic risk.

If the trunk number is high, look at your visceral fat level as well (below).

Section 6: visceral fat

Many InBody-style devices report a visceral fat level on a scale of 1 to 20, or a visceral fat area in square centimetres.

  • On the level scale, 1 to 9 is generally considered normal, and 10 and above is high.
  • On the area scale, 100 cm² is the common threshold for excess visceral fat.

Visceral fat is the fat deep in the abdomen around organs, and it's the type most strongly linked to fatty liver, insulin resistance and heart disease. Bioimpedance only estimates it, so a high number is a prompt to measure your waist and check your blood sugar and liver, not a diagnosis.

Section 7: ECW/TBW ratio (the fluid balance check)

This is the line most people skip and shouldn't. It compares water outside your cells (extracellular water, ECW) with total body water (TBW).

ECW/TBW ratio = extracellular water ÷ total body water

On most InBody reports, the normal range is about 0.360 to 0.390. Values of 0.390 to 0.400 are borderline, and above 0.400 suggest fluid retention (oedema) or, in some cases, low muscle mass and malnutrition.

Why it matters

An elevated ratio means more fluid is sitting outside cells. Causes include heart failure, kidney disease, liver disease, low protein levels, thyroid problems, long periods of standing, high salt intake, hormonal changes and medicines. If the ratio is high, take the swelling seriously and see a doctor, especially if you notice swollen ankles or breathlessness. It also warns that your lean and fat numbers may be less accurate that day.

Section 8: basal metabolic rate (BMR)

The machine estimates how many calories you burn at rest, usually from your lean mass. It's often higher than formula-based estimates for muscular people and lower for those with little muscle.

Use it as a rough starting point for calorie targets, and adjust based on your actual weight trend. Our guide on TDEE explains how.

Section 9: the score

Many reports end with a single "body composition score" out of 100, often with 80 as "average" or "good." It's calculated from your muscle relative to your weight and height. It's a motivating number, not a medical one. A rising score over months is encouraging, but don't compare it with someone else's.

Section 10: phase angle and other extras

Some devices report phase angle, an indicator of cell health and muscle quality. Higher values are generally better, and low values are associated with malnutrition and illness. It's a research-grade measure; if yours is flagged low, discuss it with a doctor rather than trying to interpret it alone.

A worked reading

Imagine this report for a 35-year-old man, 172 cm and 76 kg:

  • Skeletal muscle mass: 28.5 kg (bar slightly below range)
  • Body fat mass: 20.9 kg
  • PBF: 27.5 percent (above range)
  • BMI: 25.7
  • Visceral fat level: 11
  • ECW/TBW: 0.382
  • Segmental lean: legs at 93 percent, arms at 96 percent
  • Score: 72

What it says: he's carrying a bit too much fat and not enough muscle, with a visceral fat level that's above normal. Fluid balance is normal, so the numbers are probably reliable. The legs are the weakest region.

What to do: reduce fat mass by about 4 to 6 kg over 3 to 4 months through a small calorie deficit and more walking; do leg-focused strength work two to three times a week; make sure protein is adequate; check blood sugar, lipids and liver tests because of the visceral fat; re-test in 8 to 12 weeks under the same conditions.

How to get a useful report

  • Test in the morning, fasted, after using the toilet.
  • Avoid exercise, sauna, heavy meals and alcohol for 12 hours beforehand.
  • Remove metal, stand still, and keep hands and feet clean.
  • Use the same machine and time of day.
  • Don't test during illness or on the first days of a period if you retain a lot of fluid.
  • Keep your reports and compare the same lines over time.

What not to do with the report

  • Don't chase the score. The best use is to see whether fat is down and muscle is up.
  • Don't compare your numbers with those from a friend's different machine.
  • Don't react to single-line changes. A 0.5 kg change in muscle between two tests is within the noise.
  • Don't treat the printout as a diagnosis.

Frequently asked questions

How to read an InBody report?

Start with body fat mass and skeletal muscle mass, then look at percent body fat and visceral fat, then check the ECW/TBW ratio to see whether the reading is trustworthy. Use segmental sections to find weak or uneven areas.

What is a good muscle to fat ratio?

There's no single number. In practice you want skeletal muscle in or above its normal range and body fat in or below its normal range. Improving both over time is the goal.

Is the InBody result accurate?

Medical-grade devices are reasonably good for estimating trends. They can be off by several percentage points versus DEXA, especially with unusual hydration.

What does a high ECW/TBW ratio mean?

More water is sitting outside your cells than expected. It can reflect fluid retention from heart, kidney, liver or thyroid problems, or low muscle mass, and it's worth discussing with a doctor.

What is a normal visceral fat level?

On most scales, 1 to 9 is normal and 10 or more is high. Treat a high value as a reason to check waist, blood sugar and liver health.

How often should I do a body composition test?

Every 4 to 8 weeks is enough. More often mostly measures water.

When to see a doctor

See a doctor if your report shows a high ECW/TBW ratio along with swelling or breathlessness, very low muscle mass with weight loss, a very high visceral fat level together with high blood sugar or blood pressure, or any result that comes with symptoms.

Care at Prakash Hospital Noida

Whether you live in Sector 18, Sector 62, Greater Noida West, or anywhere nearby, Prakash Hospital Noida is a trusted name for metabolic health, weight management and preventive care in Noida. Our physicians can help you make sense of a body composition report and decide what to do next.

To book a consultation, call the number.

Sources: Misra A, Shrivastava U. Obesity and dyslipidemia in South Asians. Nutrients, 2013. Reference ranges described are those commonly printed on InBody-style reports; ranges vary by manufacturer.

Tags: #InBodyReport #BodyCompositionAnalysis #PrakashHospitalNoida

Share:

copy icon

Services we offer

We offer expert care across key specialties, including Medicine, Cardiology, Orthopaedics, ENT, Gynaecology, and more—delivering trusted treatment under one roof.

Related Articles

Articles on Nutrition

See all
Role of Nutrition in Bone Healing

Role of Nutrition in Bone Healing

Support fracture recovery with essential nutrients like calcium, vitamin D, and protein for faster bone healing.

19 Nov 2025

by Prakash Hospital

More on Hepatology

See all
लिवर खराब होने के शुरुआती लक्षण

लिवर खराब होने के शुरुआती लक्षण

लिवर खराब होने के शुरुआती लक्षण क्या हैं? थकान, पीलिया, पेट दर्द जैसे संकेतों को नज़रअंदाज़ न करें। कारण, जांच, इलाज और बचाव के तरीके जानें।

20 Feb 2026

by Prakash Hospital

Further Reading on Nutrition

Banner Background
Prakash Hospital Doctor

Looking for the Best Hospital in Noida? Talk to Our Experts

Book a consultation with Prakash Hospital's specialists — 24/7 emergency care, 100+ doctors, NABH accredited.

View All Departments